Track!

SapperAnt · Post by **SapperAnt** » Mon Jun 03, 2013 8:52 pm

I am flabberghasted by generosity.

Jenny, the very very sprightly 90 year old over the road learned via our neihgbours that like her late husband I have a garden railway. Since his death it has lain derelist. Upon learning of my interest, however, she gifted me over 25 metres of track and two pairs of points, two kit-built foot bridges, a signal and what else she can find (which includes a huge pile of 16mm today etc).

The track a Peco 0 guage: Is it possible to run live steamers on it?

Jenny's late husband obviously did because he had a Lady Anne (kit built), which Jenny is holding on to but she would like to see it run again.

pauly · Post by **pauly** » Mon Jun 03, 2013 9:40 pm

Yes you can run steamers on Peco

SapperAnt · Post by **SapperAnt** » Mon Jun 03, 2013 9:42 pm

Cool!

The only problem Ive got with the 0-gauge compared to SM32 is the rail profile - I can't join the two.

not that Im complaining. I await with wonder, and trepidation, what will emerge next from Jenny's shed.

tom_tom_go · Post by **tom_tom_go** » Mon Jun 03, 2013 10:15 pm

She probably has no idea how much the stuff is worth.

Might be a kind gesture to offer her some money.

SapperAnt · Post by **SapperAnt** » Mon Jun 03, 2013 10:20 pm

Yeah I'm fealing a bit...... "concerned" shall we say about this gift. She said it was no use to her and was just taking up space in her shed. Some of the track is damaged - there's about 30 metres in total - but the vast majority is useful.

LnBmad · Post by **LnBmad** » Mon Jun 03, 2013 10:32 pm

Can match it to sm32 if your careful where you join it.

SapperAnt · Post by **SapperAnt** » Mon Jun 03, 2013 10:35 pm

Useful to know. Care to explain?

LnBmad · Post by **LnBmad** » Mon Jun 03, 2013 10:49 pm

Get the track levels matched and cut the rail straight. Don't use fishplates and double screw both ends down. Using this method I have joined Mamod track with peco sm32 with no issues.

LnBmad · Post by **LnBmad** » Mon Jun 03, 2013 10:58 pm

Please excuse quality of photo as its dark outside but here's how I did it:

SapperAnt · Post by **SapperAnt** » Mon Jun 03, 2013 11:11 pm

You must be a mind reader! I was just going to ask for a picture of how you'd done it!

Fantastic!!

LnBmad · Post by **LnBmad** » Mon Jun 03, 2013 11:15 pm

SapperAnt:84399 wrote:You must be a mind reader! I was just going to ask for a picture of how you'd done it!

Fantastic!! :D

As you can see I ended up filing them to get it smooth but it works a treat. Never had a derailment. Should work the same using o gauge track. If. Needed to electrify it all I'd do is solder a small wire between the two pieces ad away you go

SapperAnt · Post by **SapperAnt** » Tue Jun 04, 2013 11:30 pm

Cool! thanks

upon closer inspection this old chappies line was track powered and every single joint was soldered. When the track was lifted the fishplates were just snapped. So I suspect rather a lot of de-soldering required.

Jenny - the old lady - suggests there might be more bits and pieces. And also an old O gauge Triang loco (Big big Train????)

Garden Railway Forum

Track!

Track!

Who is online