The CVLR gets it's new home (WIP railway & stock)
-
Sir haydn
- Dr. Bond of the DVLR
- Retired Director

- Posts: 4533
- Joined: Tue Jun 09, 2009 9:43 pm
- Location: Suffolk
- Contact:
-
Pendo Pilot
Decided to finally bite the bullet & start weathering my accy wagons. Maybe it's just me but I find clean wagons look wrong... :D After all my railway is not a preserved affair but a working line (set between 1920-1960). Have made a start anyway, have not done weathering like this for years since my 00 days.



(Not that it shows up very well in these pics!!)
The rest of my accy wagons are half way done as well now.
Also a few wagons arrived from the Elmtree line (Thanks Keith). After regauging them the CVLR decided to save money in expensive repaints by just modifying the GW lettering, cheapskates.




(Not that it shows up very well in these pics!!)
The rest of my accy wagons are half way done as well now.
Also a few wagons arrived from the Elmtree line (Thanks Keith). After regauging them the CVLR decided to save money in expensive repaints by just modifying the GW lettering, cheapskates.

- 90733
- Driver

- Posts: 1956
- Joined: Wed Dec 16, 2009 6:17 pm
- Location: West Yorkshire
- Contact:
-
Tom
-
Pendo Pilot
Remind me to finish the end of that brakevan!!! I just rechecked the pics & I have missed a bit..
:roll: ;)
Finished off the rest of the accy fleet & decided that was a good excuse to run them all behind a few loco's...
Whilst "playing/Operating" a recurring thought popped into my head again.

That space on the left would make a nice spot for more sidings!! I was going to leave it until I finished a circuit but as I have had no time to do groundworks for that I may just tinker with this. My thoughts are that it's a little squashed at the moment in the station area. Also with it being below ground level then you don't get to see much down there between the two embankment sides. Widening the cutting would make things more open....Hmmm.

Oh & I just liked this pic from this evening. :D (even with the oily fingermarks on the loco!)
Finished off the rest of the accy fleet & decided that was a good excuse to run them all behind a few loco's...
Whilst "playing/Operating" a recurring thought popped into my head again.

That space on the left would make a nice spot for more sidings!! I was going to leave it until I finished a circuit but as I have had no time to do groundworks for that I may just tinker with this. My thoughts are that it's a little squashed at the moment in the station area. Also with it being below ground level then you don't get to see much down there between the two embankment sides. Widening the cutting would make things more open....Hmmm.

Oh & I just liked this pic from this evening. :D (even with the oily fingermarks on the loco!)
-
mhlr
- Retired Director

- Posts: 4336
- Joined: Sun Oct 21, 2007 8:16 pm
- Location: Shropshire, England
Cut the lawn back a bit, then make it slope down more gradually to the level of the trackbed, so you get more of a veiw into it.Pendo Pilot wrote:That space on the left would make a nice spot for more sidings!! I was going to leave it until I finished a circuit but as I have had no time to do groundworks for that I may just tinker with this. My thoughts are that it's a little squashed at the moment in the station area. Also with it being below ground level then you don't get to see much down there between the two embankment sides. Widening the cutting would make things more open....Hmmm.![]()

-
MoelygestLR
-
Pendo Pilot
Well I had an hour or so spare this afternoon so I decided to just measure up the station area for widening..Then I thought I would just try something...Whoops....
So this was it before, tight, dark & hard to view...

A bit of measuring......with a shovel :roll:

There you go, that might work..






Just need to build some custom pointwork now....Hmm, never tried that before..Oh well! Two new sidings may well go in here, not sure yet. Have actually moved all the slabs back another inch or two from the trackbed now.
So this was it before, tight, dark & hard to view...

A bit of measuring......with a shovel :roll:

There you go, that might work..






Just need to build some custom pointwork now....Hmm, never tried that before..Oh well! Two new sidings may well go in here, not sure yet. Have actually moved all the slabs back another inch or two from the trackbed now.
- 90733
- Driver

- Posts: 1956
- Joined: Wed Dec 16, 2009 6:17 pm
- Location: West Yorkshire
- Contact:
-
Pendo Pilot
Feet!90733 wrote:Nice, but what are the paving for?
Going to build a sleeper built bench on the edge of the lawn, so you can just sit down there & watch trains go by hence the paving slabs. Also makes an edge to the line. Will hopefully wall it from the railway in slate. May also have a loco shed there yet, the slabs will at least allow a decent place to kneel as you fettle your loco.
Last edited by Pendo Pilot on Wed Aug 11, 2010 10:32 pm, edited 1 time in total.
- 90733
- Driver

- Posts: 1956
- Joined: Wed Dec 16, 2009 6:17 pm
- Location: West Yorkshire
- Contact:
-
Pendo Pilot
-
Pendo Pilot
Meant to add this video before. It's only a little play around I had yesterday evening. Nothing really new but if you have just over 6 minutes with nothing to do then here you are. It's now of course out of date as the lines changed since then.
<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/hXU_0RvhNkk&hl ... ram><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/hXU_0RvhNkk&hl=en_GB&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/hXU_0RvhNkk&hl ... ram><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/hXU_0RvhNkk&hl=en_GB&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
Who is online
Users browsing this forum: No registered users and 63 guests
