Prusa i3 3d printer
Re: Prusa i3 3d printer
This link explains the differences between obj and stl, although it is aimed at 3D scanning rather than 3D printing
https://matterandform.net/blog/long-live-the-obj
For what we need, I think the benefits of obj over stl are minimal to non-existant, but if your system can handle it then fine. Unfortunately my Qidi software has had that functionality removed from their customised version of Cura - there are several Cura functions that they have removed for no obvious reason.
https://matterandform.net/blog/long-live-the-obj
For what we need, I think the benefits of obj over stl are minimal to non-existant, but if your system can handle it then fine. Unfortunately my Qidi software has had that functionality removed from their customised version of Cura - there are several Cura functions that they have removed for no obvious reason.
Philip
Re: Prusa i3 3d printer
Update on progress. After the initial honeymoon period, I ran out of the small spool of green filament which was supplied with the printer and ordered some more online. When it arrived, I experienced all sorts of problems, mainly because I couldn't get the pieces I was trying to print to stick to the print bed. As you can imagine, as the printer applies a series of layers to what has already been printed, if what's been printed moves then subsequent layers can end up all over the place - the worst is to end up with a big bundle of knotted string.
It took me a while to figure out what was needed - and thanks to Philipy for stepping in and advising! But in the end, all that was needed was to replace the masking tape on the bed, clean the knurled wheel that feeds the filament to the print head and lower the temperature of the printhead by 5C. I've also decided to print a skirt around each object. Not essential but it does help to improve adhesion and also makes sure the plastic is flowing freely before it starts printing the actual piece.
I've placed the printer in another corner (away from draughts), stiffened the structure (small wobbles in the frame cause interesting corrugations in the printing) and improved the way the screw threads controlling the vertical movement are connected to the stepper motors. .
I've also ordered some bushed bearing brackets to support the tops of the threaded rods. They only cost a fiver for two (inc postage) from a UK supplier but should help improve the stability of the rods, particularly when printing taller models. In the meantime, here's progress so far on the seats ... .
I've been tinkering with the settings in between each print, but now think I've now got the definitive version of each. The learning curve is beginning to flatten out!! Here's the printer in action, printing one of the seats. .
MetalMuncher suggested this was more of a project than a printer. He's quite right. But in many ways, I feel I'm learning more by having to fiddle and tweak to get it working as reliably as I would want. I'm hoping I can improve the quality of the prints as I make these improvements. Until I reach the stage, maybe, where I've taken it as far as I can - then maybe Santa might be feeling generous.
Rik
It took me a while to figure out what was needed - and thanks to Philipy for stepping in and advising! But in the end, all that was needed was to replace the masking tape on the bed, clean the knurled wheel that feeds the filament to the print head and lower the temperature of the printhead by 5C. I've also decided to print a skirt around each object. Not essential but it does help to improve adhesion and also makes sure the plastic is flowing freely before it starts printing the actual piece.
I've placed the printer in another corner (away from draughts), stiffened the structure (small wobbles in the frame cause interesting corrugations in the printing) and improved the way the screw threads controlling the vertical movement are connected to the stepper motors. .
I've also ordered some bushed bearing brackets to support the tops of the threaded rods. They only cost a fiver for two (inc postage) from a UK supplier but should help improve the stability of the rods, particularly when printing taller models. In the meantime, here's progress so far on the seats ... .
I've been tinkering with the settings in between each print, but now think I've now got the definitive version of each. The learning curve is beginning to flatten out!! Here's the printer in action, printing one of the seats. .
MetalMuncher suggested this was more of a project than a printer. He's quite right. But in many ways, I feel I'm learning more by having to fiddle and tweak to get it working as reliably as I would want. I'm hoping I can improve the quality of the prints as I make these improvements. Until I reach the stage, maybe, where I've taken it as far as I can - then maybe Santa might be feeling generous.
Rik
Re: Prusa i3 3d printer
Glad you're getting there Rik.ge_rik wrote: ↑Sat May 02, 2020 11:42 am MetalMuncher suggested this was more of a project than a printer. He's quite right. But in many ways, I feel I'm learning more by having to fiddle and tweak to get it working as reliably as I would want. I'm hoping I can improve the quality of the prints as I make these improvements. Until I reach the stage, maybe, where I've taken it as far as I can - then maybe Santa might be feeling generous.
As I said once before about my own experiences many moons ago, beating the learning curve and making the @$?&%$! machine do what I want is satisfaction in itself.
Then eventually you get to the point of being able to use it as any other tool in the box without thinking - last week I realised that somewhere over the winter I had lost a small part for the rain sensor on the garden irrigation system. Half an hour of drawing and half an hour printing and I have a new one - in black, not the horrible bright orange of the 'proper' one!!
Philip
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Prusa i3 3d printer
I think this scenario Rik is equivalent to my situation where I am tempted to buy a cheap worktop lathe but the reality is I need something more substantial.
However, as you say you now know what you need now through experience which sometimes is the only way to find out (mostly how I learn!).
However, as you say you now know what you need now through experience which sometimes is the only way to find out (mostly how I learn!).
Re: Prusa i3 3d printer
I'm looking forward to reaching that stage!philipy wrote: ↑Sat May 02, 2020 12:13 pm ......- last week I realised that somewhere over the winter I had lost a small part for the rain sensor on the garden irrigation system. Half an hour of drawing and half an hour printing and I have a new one - in black, not the horrible bright orange of the 'proper' one!!
I can remember when I first started scratch bashing locos and stock. I used to dread the painting process. Now I've been through several minor disasters with runs, paint reacting to primer, paint reacting to varnish, plasticard reacting to glue etc etc etc, I've reached the stage where, if something goes wrong, I just tut a few times and get on with it.
I'm hoping it won't be long before I feel the same about the printer.
Rik
Re: Prusa i3 3d printer
I'm writing a series of blog posts about my experiences with the printer. Here's the first - a guide to assembling it. Working on the principle that there may be others who found the instructions difficult to follow or, in my case, for a different printer, I thought there may be a few people out there who would like an illustrated guide to its assembly.
https://riksrailway.blogspot.com/2020/0 ... et-a8.html
Rik
https://riksrailway.blogspot.com/2020/0 ... et-a8.html
Rik
- GAP
- Trainee Driver
- Posts: 694
- Joined: Sun Dec 23, 2012 10:34 pm
- Location: Bundaberg QLD Australia
- Contact:
Re: Prusa i3 3d printer
Looks good Rik, now I just need to find a reason to buy a 3D printer so I can use the instructions.ge_rik wrote: ↑Sun Jun 21, 2020 4:30 pm I'm writing a series of blog posts about my experiences with the printer. Here's the first - a guide to assembling it. Working on the principle that there may be others who found the instructions difficult to follow or, in my case, for a different printer, I thought there may be a few people out there who would like an illustrated guide to its assembly.
https://riksrailway.blogspot.com/2020/0 ... et-a8.html
Rik
Graeme
From the home of the Ringbalin Light Railway
https://ringbalin-light-railway.blogspo ... -page.html
From the home of the Ringbalin Light Railway
https://ringbalin-light-railway.blogspo ... -page.html
Re: Prusa i3 3d printer
Is there no end to your skill and talent Rik. You have done a great job with the locos and now there will be no stopping you with even more brilliant builds..
ROD
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
Re: Prusa i3 3d printer
One other thing Rik, do they need to be in a reasonably dust free environment
I have seen 3D printers that are in some sort of enclosure. I am not thinking of getting a printer mate, even though I set up CNC pipe benders, the intricate things that need to be done to print something would be far beyond me....
I have seen 3D printers that are in some sort of enclosure. I am not thinking of getting a printer mate, even though I set up CNC pipe benders, the intricate things that need to be done to print something would be far beyond me....
ROD
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
Re: Prusa i3 3d printer
If I can interject here, the answer is "reasonably" i.e. I wouldn't use mine and have a mechanical sander going at the same time, but I haven't found normal household/modelling activities to be an issue.
A couple of days ago I had been outside mowing the grass and then came in to set the printer going. Without me realising it a couple of grass clippings must have fallen into the machine and landed on the bed.... I only found out when I removed the two pieces from the machine subsequently.....
FWIW, they are permanently embedded and haven't affected to print on the faces underneath, that you can't see here.
My Qidi is in an enclosure, it comes as standard, but enclosures are more to do with maintaining an even temperature for some print materials, one being ABS. PLA, which is probably the the most common material, wants to be kept cool so the enclosure is opened and the nozzle fans turned on. In this case of course, having no enclsure simply isn't an issue.
Philip
Re: Prusa i3 3d printer
No, he's working well, but he only does the back lawn so I have to do the front myself every couple of weeks.
Philip
Who is online
Users browsing this forum: No registered users and 1 guest