Drilling holes in metal angle
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Drilling holes in metal angle
I have some 10×10mm aluminium angle that I want to use as strapping for a wagon but I need to drill holes that will line up and then be able to produce identical pieces.
Making a template sounds the way to go but then how do you make the template accurate?
I have a pillar drill if that helps although I doubt it will accurately produce what I need as it was cheap.
Making a template sounds the way to go but then how do you make the template accurate?
I have a pillar drill if that helps although I doubt it will accurately produce what I need as it was cheap.
- Busted Bricks
- Trainee Driver
- Posts: 750
- Joined: Sat Jan 22, 2011 9:16 pm
- Location: Denmark
- Contact:
Re: Drilling holes in metal angle
Print it, stick it on with a glue stick, centerpunch, drill. That's how I do it.
Re: Drilling holes in metal angle
I would get a strip of steel (thicker if possible than the aluminium) and drill the required holes in that such that it can be clamped inside the aluminium angle. Then use that as the drilling jig to make the holes in multiple pieces. Quick and rough pic. below.
Grant.
Grant.
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Drilling holes in metal angle
I had that idea as well Grant but then how do you create your template piece accurately?
Maybe a combination of both ideas will work. Seems like a lot of effort though but then I guess that is why stuff like this ready made is expensive.
Maybe a combination of both ideas will work. Seems like a lot of effort though but then I guess that is why stuff like this ready made is expensive.
Re: Drilling holes in metal angle
Well I guess that comes down to experience Tom, a marking gauge would create the line then accurate measurement for the spacing. Using a jig, at least they will all be identical. Good luck.but then how do you create your template piece accurately?
Grant.
Re: Drilling holes in metal angle
Tom,tom_tom_go wrote: ↑Sun Oct 01, 2017 11:10 am I had that idea as well Grant but then how do you create your template piece accurately?
The laymans version of Grants suggestion, which works for me:
1) Coat the template blank with permanent marker and allow to dry.
2) Scribe the centre line using a pair of dividers with the legs set at odd lengths so you can run the longer one down the edge and mark with the shorter one.
3) Set the divider legs back to equal, and then adjust to the rivet centres that you want.
4) Mark the position of the first rivet by scribing a cross on the centre line.
5) Place one leg of the dividers on that cross, then wiggle it to mark the position of the next rivet on the centre line.
6) "Walk"the dividers down the centre line, scribing/marking each one as you go.
7) Centre pop each rivet position, then drill a small pilot for each hole, then open up to your finished size.
Sounds a lot more complicated and time consuming than it is to actually do.
Philip
Re: Drilling holes in metal angle
I second that. A set of dividers are one of those tools that once you have used them, you never know how you managed with out.
If at first you don't succeed, use a bigger hammer!
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Drilling holes in metal angle
Divider set recommendations please as there are loads to choose from?
Re: Drilling holes in metal angle
Silverline, Sealy or Draper should be okay and won't break the bank.
If at first you don't succeed, use a bigger hammer!
Re: Drilling holes in metal angle
3" engineers dividers will do the job. I've also got a pair of 6" dividers, but can't remember when I last used the larger ones.tom_tom_go wrote: ↑Sun Oct 01, 2017 1:52 pm Divider set recommendations please as there are loads to choose from?
https://www.chronos.ltd.uk/acatalog/info%2dD3%2ehtml
You don't have to buy them off Chronos, there are other suppliers and the link is just to show you what you are looking for.
The specialist tool for marking out a set distance from an edge are called jenny calipers, but spring type engineers dividers will also do that job, as well as laying out a series of equal intervals.
If you don't already have some, also get a couple of small metal (not plastic) g-clamps to hold the jig in place while drilling the workpiece.
Regards,
Graeme
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Drilling holes in metal angle
Thank you for all your replies, makes the forum worth hosting!
I will have a go and let you know how I get on.
I will have a go and let you know how I get on.
-
- Trainee Fireman
- Posts: 116
- Joined: Mon Mar 26, 2012 4:00 am
- Location: Wodonga, Vic. Land of Oz
Re: Drilling holes in metal angle
Here's something that somtime's works for me.
go to a $2.00 (1 pound?) shop and buy a cheep metal ruler.
Pick a spacing which will suit your purposes (every 'x' mm).
Clamp a fence on your pillar drill that is spaced the distance from the bit to the inside of the angle (or edge if piece to be drilled is flat).
Proceed to drill the ruler at your chosen intervals, you can 'feel' the markings on the ruler because they are eched into the surface.
Use the drilled ruler to mark the work with a centre punch or just a nail.
Of course this only works if your spacing is exact mm's or fractions of an inch.
Cheep, and you can maybe use it again.
Tim
go to a $2.00 (1 pound?) shop and buy a cheep metal ruler.
Pick a spacing which will suit your purposes (every 'x' mm).
Clamp a fence on your pillar drill that is spaced the distance from the bit to the inside of the angle (or edge if piece to be drilled is flat).
Proceed to drill the ruler at your chosen intervals, you can 'feel' the markings on the ruler because they are eched into the surface.
Use the drilled ruler to mark the work with a centre punch or just a nail.
Of course this only works if your spacing is exact mm's or fractions of an inch.
Cheep, and you can maybe use it again.
Tim
Re: Drilling holes in metal angle
That's a great piece of lateral thinking Tim.
Grant.
Grant.
Re: Drilling holes in metal angle
What a good idea - filed for future use!11thHour wrote: ↑Tue Oct 03, 2017 7:58 am Here's something that somtime's works for me.
go to a $2.00 (1 pound?) shop and buy a cheep metal ruler.
Pick a spacing which will suit your purposes (every 'x' mm).
Clamp a fence on your pillar drill that is spaced the distance from the bit to the inside of the angle (or edge if piece to be drilled is flat).
Proceed to drill the ruler at your chosen intervals, you can 'feel' the markings on the ruler because they are eched into the surface.
Use the drilled ruler to mark the work with a centre punch or just a nail.
Of course this only works if your spacing is exact mm's or fractions of an inch.
Cheep, and you can maybe use it again.
Tim
Phil
Sporadic Garden Railer who's inconsistencies know no bounds
My Line - https://gardenrails.org/forum/viewtopic ... 41&t=11077
Sporadic Garden Railer who's inconsistencies know no bounds
My Line - https://gardenrails.org/forum/viewtopic ... 41&t=11077
Re: Drilling holes in metal angle
That is a plan of extreme cunningness.
If at first you don't succeed, use a bigger hammer!
Re: Drilling holes in metal angle
Brilliant Tim, and yes you would be able to use again, but i would drill a flat piece of Aluminium and use that has the template. You can always use the ruler again to drill out another piece if and when the 1st one gets unusable.
ROD
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
-
- Cleaner
- Posts: 39
- Joined: Sat Nov 24, 2018 10:54 am
- Location: Bournemouth
Re: Drilling holes in metal angle
Sorry for the late reply but have just spotted this one. A useful little tool for scribing a line parallel to an edge is a pair of odd leg dividers, which has one leg with its end either curved or angled to run along the edge of the workpiece.
Re: Drilling holes in metal angle
Ditto (ie Wot he sed)
Rik
PS Blimey, just seen the original was posted in October - must have missed this one
Re: Drilling holes in metal angle
A carpenters marking gauge will make a line parallel to an edge.
Don
Don
- Busted Bricks
- Trainee Driver
- Posts: 750
- Joined: Sat Jan 22, 2011 9:16 pm
- Location: Denmark
- Contact:
Re: Drilling holes in metal angle
That was before I got the laser - now I draw the holes in CAD and let the laser cut themBusted Bricks wrote: ↑Sat Sep 30, 2017 5:17 pm Print it, stick it on with a glue stick, centerpunch, drill. That's how I do it.
Who is online
Users browsing this forum: No registered users and 3 guests