Summertime, and your printer's seem idle?

A place where discussions are about 3D printing.
User avatar
-steves-
Administrator
Administrator
Posts: 2412
Joined: Thu Jul 28, 2011 1:50 pm
Location: Cambridge & Peterborough

Re: Summertime, and your printer's seem idle?

Post by -steves- » Mon May 23, 2022 6:47 pm

OK, wrapped up, hopefully being collected tomorrow, so should be with you on Thursday.

A few little extra bits in there, hope you can make use of them. :)
The buck stops here .......

Ditton Meadow Light Railway (DMLR)
Member of Peterborough and District Association
http://peterborough.16mm.org.uk/

Phil.P
Fireman
Fireman
Posts: 430
Joined: Thu Jan 31, 2019 3:28 pm
Location: Staffs. UK

Re: Summertime, and your printer's seem idle?

Post by Phil.P » Tue May 24, 2022 12:07 am

Intriguing...

:?

Phil.P
Fireman
Fireman
Posts: 430
Joined: Thu Jan 31, 2019 3:28 pm
Location: Staffs. UK

Re: Summertime, and your printer's seem idle?

Post by Phil.P » Thu May 26, 2022 3:15 pm

Post has arrived...

Stern looks, from Domestic Authorities.. :? :lol:

One parcel from Peter Binnie. - Strange! I seem to have ordered four chassis. ;)

So now I have the major components of three 'Windy'..

Steve, thank you for the other bits and pieces. They raise a number of questions, but probably for a different time and place?

(But did you intend to drop a motor in the box?)

The power of the Community, wins again.
Another 'thank you' to you both.

Phil Partridge.

User avatar
-steves-
Administrator
Administrator
Posts: 2412
Joined: Thu Jul 28, 2011 1:50 pm
Location: Cambridge & Peterborough

Re: Summertime, and your printer's seem idle?

Post by -steves- » Thu May 26, 2022 6:23 pm

Phil.P wrote: Thu May 26, 2022 3:15 pm Post has arrived...

Stern looks, from Domestic Authorities.. :? :lol:

One parcel from Peter Binnie. - Strange! I seem to have ordered four chassis. ;)

So now I have the major components of three 'Windy'..

Steve, thank you for the other bits and pieces. They raise a number of questions, but probably for a different time and place?

(But did you intend to drop a motor in the box?)

The power of the Community, wins again.
Another 'thank you' to you both.

Phil Partridge.
Yes, I have loads and loads of motors and I just wanted to make sure you had something that fitted, it's a 3v-6v motor.

Hopefully all of the contents was useful?
The buck stops here .......

Ditton Meadow Light Railway (DMLR)
Member of Peterborough and District Association
http://peterborough.16mm.org.uk/

Phil.P
Fireman
Fireman
Posts: 430
Joined: Thu Jan 31, 2019 3:28 pm
Location: Staffs. UK

Re: Summertime, and your printer's seem idle?

Post by Phil.P » Thu May 26, 2022 8:31 pm

Yes, thank you..
Payment made.

Thanks again Steve,
Phil.

Phil.P
Fireman
Fireman
Posts: 430
Joined: Thu Jan 31, 2019 3:28 pm
Location: Staffs. UK

Re: Summertime, and your printer's seem idle?

Post by Phil.P » Thu Jun 09, 2022 10:06 am

For anyone Vaguely interested:
The 'quick' distraction-project, has grown wings (propellers?)..
The performance (on a windy day, and roughly thrown-down track) was disappointing. :dontknow:

The wind blew 'Windy' backwards, and there was not enough 'oomph' to get up the slopes..

The Tamiya liquid cement, doesn't seem to work-well, with Binnie plastic. - Axle-boxes fell off, but that is good, as I am hunting for metal wheel-sets.
Flanged bearings, are on their way from the USA..
The hunt for a commercial propeller, continues..

No pictures, until I have something running better. - I am not going to paint, until I know if I am going to have to chop things about.. :ugeek :twisted:

Phil.P

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests