Wild Rose ~ Quarry Hunslet
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Wild Rose ~ Quarry Hunslet
Looking forward to seeing this run.
Remind me, is it still able to be a dual fuel burner?
Remind me, is it still able to be a dual fuel burner?
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
Me too
Yes I hope to also fire it by gas or liquid fuel
Yes I hope to also fire it by gas or liquid fuel
Best wishes,
Dave
Dave
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
I've just soldered in the water return pipes for the bypass valves. Hopefully the water won't shoot out of the filler
Best wishes,
Dave
Dave
Re: Wild Rose ~ Quarry Hunslet
Very neat job Dave.
ROD
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Wild Rose ~ Quarry Hunslet
That's lovely workmanship. Something I could only admire and dream about doing.
Ian
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
We're getting there, very slowly. Boiler feed fitted
Best wishes,
Dave
Dave
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Wild Rose ~ Quarry Hunslet
It's starting to look finished Dave, looking forward to seeing it run.
How long do you think before first test on your line?
How long do you think before first test on your line?
Re: Wild Rose ~ Quarry Hunslet
Nice Dave….Very good bit of engineering that.
ROD
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
Life is so easy when I run my trains.
https://gardenrails.org/forum/viewtopic ... 41&t=11364
https://www.youtube.com/@fairywoodlightrailway
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
Thank you chaps.
I'm not sure when it will be running on the line. I want to test the pumps against boiler pressure though
I'm not sure when it will be running on the line. I want to test the pumps against boiler pressure though
Best wishes,
Dave
Dave
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
Pushing on with the blower. I drilled the nozzle 0.45mm diameter as my small Jacobs chuck couldn't grip anything smaller
Best wishes,
Dave
Dave
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Wild Rose ~ Quarry Hunslet
Good trick I learned from TonyW is to fill the boiler up with water until you get about 40 PSI and then open the blower.
If you get a nice fountain shooting out the chimney you know the blower position is going to be efficient!
If you get a nice fountain shooting out the chimney you know the blower position is going to be efficient!
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
Splendid, a working saddle tank! It gives the little loco something special..
"En schöne Gruess" from an Alpine railway in Holland.
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
I need to connect the to-be-built reverser to the reversing valve. eBay supplied some nice stainless 2mm Bowden cable inner that fits nicely in 1/8 K&S brass tubing it seems rigid enough for pull and push operation.
Best wishes,
Dave
Dave
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
Before I can make the reverser I need to make the bodywork to see how much space is available for it. One side is now complete, the other is in progress.
The main panel is a piece of 0.6mm steel sheet bent around a 1/4" bar for the radius. The top piece is 1/4" x 1/16" strip brazed into a 90 deg angle. It's all soft soldered together
The main panel is a piece of 0.6mm steel sheet bent around a 1/4" bar for the radius. The top piece is 1/4" x 1/16" strip brazed into a 90 deg angle. It's all soft soldered together
Best wishes,
Dave
Dave
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
Second side completed on this hot Auckland Anniversary day
- Attachments
-
- IMG_20190128_162946.jpg (41.95 KiB) Viewed 6111 times
Best wishes,
Dave
Dave
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Re: Wild Rose ~ Quarry Hunslet
Solid work, is steel easier to soft solder than brass?
- dewintondave
- Trainee Driver
- Posts: 697
- Joined: Mon Mar 07, 2011 8:52 am
- Location: New Zealand
Re: Wild Rose ~ Quarry Hunslet
Steel solders very easily with zinc chloride flux
It was easier than soldering the copper/brass tank Tom
It was easier than soldering the copper/brass tank Tom
Best wishes,
Dave
Dave
Who is online
Users browsing this forum: No registered users and 19 guests