Search found 432 matches
- Sun Mar 31, 2024 8:29 pm
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
To answer the last two posts, in order: A 100 ohm pot getting hot, across the speaker output is a little worrying. - I don't have one of these cards to play with / work out the circuit, so advise caution, until 'we' can find more detail. The second query, is easier to answer : These cards are set up...
- Sun Mar 31, 2024 2:46 pm
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
Just take a breath, Guys.... These cards are fed with a variable width servo pulse, not a logic '0' or '1', so the 1k or 4k7 resistor is not required. Adding resistors here will not reduce the sound-level. To add a volume control, you could add a 100 ohm pot across the speaker output, and the speake...
- Sat Mar 30, 2024 9:44 pm
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
I would be a little wary of powering these Soundcards from the MR603 onboard regulator.
I draw your attention to the following extract from the MR603 manual:
"3.3V from the on-board regulator which can supply a max of 200mA"
Phil.P
I draw your attention to the following extract from the MR603 manual:
"3.3V from the on-board regulator which can supply a max of 200mA"
Phil.P
- Thu Mar 28, 2024 9:28 am
- Forum: Locomotives - Live Steam
- Topic: Ooops! - I have bought this
- Replies: 17
- Views: 4325
Re: Ooops! - I have bought this
Thanks for the comments..
More to think about.. I will possibly (weather permitting) be amongst other's with more knowledge on Saturday..
Phil.P
More to think about.. I will possibly (weather permitting) be amongst other's with more knowledge on Saturday..
Phil.P
- Thu Mar 28, 2024 9:14 am
- Forum: Projects
- Topic: Gmeinder & Co loco
- Replies: 99
- Views: 2659
Re: Gmeinder & Co loco
I don't think it was standard, and may be considered as a step too far, in authenticity?
I think I would leave it off.
Phil.P
I think I would leave it off.
Phil.P
- Thu Mar 28, 2024 9:09 am
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
A Micron supplied MR603c does not have a pin configured for a servo output by default. - It will need programing. A RC Trains supplied MR603c (look for the label, or 'T' hand-written on one of the chips) has a servo output, for external ESC or soundcard, configured on Pin6 in RC Trains configuration...
- Wed Mar 27, 2024 9:26 pm
- Forum: Locomotives - Live Steam
- Topic: Ooops! - I have bought this
- Replies: 17
- Views: 4325
Re: Ooops! - I have bought this
So did you get the old Anna going once she arrived? These old Beck have brass boilers, something to keep an eye on and drain dry when the locomotive is not in service to prevent the water from drawing the zinc out of the brass. Yes the notch is for a servo rod to go forward to a crank arm mounted i...
- Tue Mar 26, 2024 10:01 am
- Forum: Projects
- Topic: Gmeinder & Co loco
- Replies: 99
- Views: 2659
Re: Gmeinder & Co loco
Now there is a challenge for the weathering experts!
A little sad, when the custodians of heritage let it rot, but I suppose there is only some much time, money, and man-hours?
Phil.P
A little sad, when the custodians of heritage let it rot, but I suppose there is only some much time, money, and man-hours?
Phil.P
- Sat Mar 23, 2024 9:58 pm
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
Not sure if Andy has any Tx2 left?
I am into single-figures, then it becomes a little more of a job. - The Micron module is a different beast, but the peripherals remain the same.
Phil.P
I am into single-figures, then it becomes a little more of a job. - The Micron module is a different beast, but the peripherals remain the same.
Phil.P
- Fri Mar 22, 2024 4:41 pm
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
- Fri Mar 22, 2024 4:24 pm
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
Rik, You said: Moving the direction switch to the "forward" position should increment the fashing by one flash. So, if it flashes once, clicking the direction switch forward should make it flash twice, clicking it forward again should increase it to three. Is that what you mean by "in...
- Fri Mar 22, 2024 10:17 am
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
If you can change the number of flashes for the other options, you should be able to change any of them. - You are sending the same commands.. It could be you have either an older/earlier version receiver, and the firmware is slightly different. Or, There could be a 'feature' in the code in the rece...
- Thu Mar 21, 2024 5:35 pm
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
3,2,1,1 Would set Pin2 to be a servo output, following Ch1 (throttle). Getting the receiver into programming mode, will be the problem.. Would be less than a minute, with a Tx20. I ought to know where in the country you are, but the brain isn't retrieving the information so well, these days.. We are...
- Thu Mar 21, 2024 10:57 am
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
You can prove that Ch4 is driving the soundcard, by setting your Tx22 to control Ch4 from the Inertia pot. - It will be centre-off, so you will need to set it to the mid position.. A programming change (on the receiver) will be needed, to set up P2 to be a servo output following H1 (the speed contro...
- Thu Mar 21, 2024 10:11 am
- Forum: 3D Printing
- Topic: Using TinkerCAD to produce drawings for 3-D Printing
- Replies: 29
- Views: 21241
Re: Using TinkerCAD to produce drawings for 3-D Printing
Perhaps he is talking through his PPE?
Phil.P
Phil.P
- Thu Mar 21, 2024 10:07 am
- Forum: General Garden Railways
- Topic: Cheapo diesel sound card
- Replies: 123
- Views: 2394
Re: Cheapo diesel sound card
P2/Ch4
I think that is your problem?
The throttle output will be Ch1.
Unless you have a way of driving Ch4, there will not be an output.
I think that what Andy has done, is give you a servo output on P2, which is controlled by Ch4. - Possibly a misunderstanding, between the two of you?
Phil.P
I think that is your problem?
The throttle output will be Ch1.
Unless you have a way of driving Ch4, there will not be an output.
I think that what Andy has done, is give you a servo output on P2, which is controlled by Ch4. - Possibly a misunderstanding, between the two of you?
Phil.P
- Wed Mar 20, 2024 5:19 pm
- Forum: Railways & Layouts
- Topic: Here's the land for the future railroad
- Replies: 9
- Views: 310
Re: Here's the land for the future railroad
It is at times like this, an aerial shot from a drone, would put the whole kit and caboodle into perspective. An area like that, in our (wet) 'green and pleasant land' would turn into a jungle, in a single season. - I am guessing it is dry enough that the vegetation does not get out of hand easily? ...
- Sun Mar 17, 2024 11:02 am
- Forum: General Garden Railways
- Topic: What filler?
- Replies: 7
- Views: 216
Re: What filler?
Really useful, thank you...
I have not had much luck with model fillers.. Either it was solid when bought (cheap) or used a tiny bit, and the rest went off in the tube..
Had not come across AK modelling filler.. I will have to look out for that one.
Phil.P
I have not had much luck with model fillers.. Either it was solid when bought (cheap) or used a tiny bit, and the rest went off in the tube..
Had not come across AK modelling filler.. I will have to look out for that one.
Phil.P
- Fri Mar 15, 2024 11:35 am
- Forum: Projects
- Topic: Gmeinder & Co loco
- Replies: 99
- Views: 2659
Re: Gmeinder & Co loco
Increase the series resistor, and 'weather' the LED..
Phil.P
Phil.P
- Thu Mar 14, 2024 2:31 pm
- Forum: Railways & Layouts
- Topic: The Railway in the Valley of the Mill
- Replies: 338
- Views: 70582
Re: The Railway in the Valley of the Mill
That must be a 'scale' 5.6mm.
Damn those pesky decimal-places!
Phil.P
Damn those pesky decimal-places!
Phil.P