Merlin Spares

Discussion of Live Steam locomotives should be located here

Moderators: Big Jim, laalratty

Post Reply
Gareth McGrillen
Posts: 3
Joined: Sun Jan 13, 2019 6:07 pm

Merlin Spares

Post by Gareth McGrillen » Mon Jan 14, 2019 5:15 pm

Hello,
I am new to G scale live steam modelling and have recently inherited my Grandfathers Merlin gas locomotive. I originally had to fix the servo control circuit and in doing so I snapped a bolt on the gas/ignition system.

Does anyone know where I can buy replacement parts fro Merlin locomotives.

To those more familiar with these systems it is hollow - I assume to allow gas to flow through it if that helps.

Thank you

User avatar
MRail
Cleaner
Cleaner
Posts: 35
Joined: Mon Oct 26, 2009 4:16 pm
Location: Merseyside, UK
Contact:

Re: Merlin Spares

Post by MRail » Wed Jan 16, 2019 10:44 am

Gareth,
Your description sounds like a "banjo" bolt.
Merlin are long defunct, so parts are unavailable.
A model tool/screw supplier may be able to help, but you would need to know the size & thread pitch etc.

Alternatively a Merlin owner may have some better suggestions.
Must say, there have been no replies yet!

A model engineer, such as Tony at Rhos Helyg may be able to make/adapt something to fit.

Good luck!
Rob G
Madog & Mersey Railway (SM32)
In my Father's roundhouse are many loco sheds.

User avatar
TonyW
Driver
Driver
Posts: 1178
Joined: Fri May 16, 2008 9:25 am
Location: North Wales
Contact:

Re: Merlin Spares

Post by TonyW » Wed Jan 16, 2019 11:28 am

MRail wrote:
Wed Jan 16, 2019 10:44 am
A model engineer, such as Tony at Rhos Helyg may be able to make/adapt something to fit.
Thanks for the recommendation Rob, but unfortunately I cannot help.

My suggestion would be to contact Simon Whenmouth at http://www.anythingnarrowgauge.co.uk/
Tony Willmore
Rhos Helyg Locomotive Works: http://www.rhoshelyg.me.uk
Facebook: https://www.facebook.com/RhosHelygLocoWorks

Gareth McGrillen
Posts: 3
Joined: Sun Jan 13, 2019 6:07 pm

Re: Merlin Spares

Post by Gareth McGrillen » Wed Jan 16, 2019 12:34 pm

Thank you for the advice. I will email Simon and will post the outcome at later date on the forum.

Gareth

Big Jim
Director
Director
Posts: 2616
Joined: Sat Jul 06, 2013 5:28 pm
Location: Near Llanelli

Re: Merlin Spares

Post by Big Jim » Wed Jan 16, 2019 11:28 pm

As Tony said try Simon.
However, banjo bolts are used on a lot of other things, fuel systems on cars for one. If you have a local Diesel injection specialist they may be able to help If you take along the parts.

Can you post a picture of the bits and where it screws in to?
If at first you don't succeed, use a bigger hammer!

Gareth McGrillen
Posts: 3
Joined: Sun Jan 13, 2019 6:07 pm

Re: Merlin Spares

Post by Gareth McGrillen » Thu Jan 17, 2019 10:29 am

Here are three images depicting the broken part and the cab showing where it went.
Attachments
Merlin 1 (3).JPG
Merlin.png
Merlin.jpg

strettonsteamer
Cleaner
Cleaner
Posts: 5
Joined: Tue Mar 28, 2017 11:29 pm

Re: Merlin Spares

Post by strettonsteamer » Fri Jan 18, 2019 11:39 am

Hi Gareth
The Merlin banjo thread size is M5 x 0.8mm. They also used PTFE washers to seal the joint.
Hope this helps.
Regards
Ian

Post Reply

Who is online

Users browsing this forum: No registered users and 4 guests