The Leawarra Nayook Railway
Thank you one and all for your kind comments, they are much appreciated. Makes lying around on the ground with blocks of wood or bricks for the camera to take photos all seem worth it. If I can inspire others that might make up for the inspiration and ideas I have gleaned from the forum in the past and will continue to do in the future.
Grant.
Grant.
It's certainly worth the extra effort. Great atmosphere on your railway.LNR:117858 wrote:Thank you one and all for your kind comments, they are much appreciated. Makes lying around on the ground with blocks of wood or bricks for the camera to take photos all seem worth it. If I can inspire others that might make up for the inspiration and ideas I have gleaned from the forum in the past and will continue to do in the future.
Grant.
BTW, what did you use for the canvas hose on the water crane? Looks spot-on.
Rik
Very clever - looks just right!LNR:117860 wrote:Rik, the bags on the water cranes are the hemmed parts from the sleeves of khaki cotton shirts, frayed at the bottom with an exacto knife. I use the shirt material for tarps and other "canvas" bits, and the hems were left overs that happened to prove useful.
Grant.
Rik
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Ha ha, Sorry, I just saw your response!LNR:117036 wrote:PROOF!
Just for you Keith, blowing a bit of a gale but I steamed up the loco again today. Lighter train, but once again no mess. Don't know
if this shows it "no mess Charlie"
Like I said, black thing in a black hole.
After running bunker first back to Leawarra, the smokebox and frontplate would usually be spattered with fine oil and water. :lol:
I'm pleased that I managed to get you to show us more photos of that lovely engine!
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
Hi Tom and thank you,
The loco is a home build, but using a Roundhouse Katy boiler and cylinders, axles and some motion, with my own frames, rods, body, wheels, trucks etc. I bought a Katy frame and boiler kit, used the frames wheels and axles to make my petrol/mechanical loco, and the boiler cylinders and gear for this loco.
I wanted to build one of the 2ft. gauge Bagnalls from the Sth. African Avontuur line, but found outside frames on a leading four wheel truck at 45mm gauge would'nt negotiate my points, so the loco is a freelance 2-6-2, with I'd like to think a hint of the said Bagnalls.
The smokebox is quite long as it actually extends back to nearly the first boiler band, so it's a good echo chamber. It steams well even on 42mm wheels, and is quite heavy so has plenty of momentum.
Grant.
The loco is a home build, but using a Roundhouse Katy boiler and cylinders, axles and some motion, with my own frames, rods, body, wheels, trucks etc. I bought a Katy frame and boiler kit, used the frames wheels and axles to make my petrol/mechanical loco, and the boiler cylinders and gear for this loco.
I wanted to build one of the 2ft. gauge Bagnalls from the Sth. African Avontuur line, but found outside frames on a leading four wheel truck at 45mm gauge would'nt negotiate my points, so the loco is a freelance 2-6-2, with I'd like to think a hint of the said Bagnalls.
The smokebox is quite long as it actually extends back to nearly the first boiler band, so it's a good echo chamber. It steams well even on 42mm wheels, and is quite heavy so has plenty of momentum.
Grant.
- tom_tom_go
- Driver
- Posts: 4824
- Joined: Wed Feb 23, 2011 3:08 am
- Location: Kent, UK
- Contact:
When I built an interlocked signal and ground-frame on the mainline of the LNR, it started me thinking about a platform mounted ground frame operating a couple of signals, and maybe a set of points. Somehow the thought of a set of levers, maybe three minimum, open to the operating side intrigued me, and I have re-visited the thought repeatedly.
Firstly, let me say I don't profess to know much about signalling, but I have worked out that Leawarra could support a home signal on the main, with perhaps a dwarf signal on number three road, and maybe some point control. Now whether these become inter-locked only time will tell, but to start things off I am building another home signal.
Being able to make an exact copy of the previous one I thought this would be easy. Silly me! You don't have to be far out to totally change the angles that the signal arm and spectacle assume when moved by the control rodding. I should have known better.
So when I finish the signal, and if I have any hair left, we shall think about interlocking and the dwarf signal.
One step at a time, this is definitely a work in progress and to quote a bard on this forum, "this is what keeps us awake at nights".
Grant.
Firstly, let me say I don't profess to know much about signalling, but I have worked out that Leawarra could support a home signal on the main, with perhaps a dwarf signal on number three road, and maybe some point control. Now whether these become inter-locked only time will tell, but to start things off I am building another home signal.
Being able to make an exact copy of the previous one I thought this would be easy. Silly me! You don't have to be far out to totally change the angles that the signal arm and spectacle assume when moved by the control rodding. I should have known better.
So when I finish the signal, and if I have any hair left, we shall think about interlocking and the dwarf signal.
One step at a time, this is definitely a work in progress and to quote a bard on this forum, "this is what keeps us awake at nights".
Grant.
Well Rik, that patience was surely tried today. Made the finial (brass this time) and the operating lever bracket, then the lever itself. Easy!
Then the horror job, Worrying (engineering term) a slot 1/16thx7/32" through a piece of 3/4" M.S. bar for the lever weight. My longest 1/16th end mill was about 1/4" long, so three 1/16th holes in a line, join them up with the end mill to 1/4" deep then the rest of the afternoon wearing away the bit in the middle till I could finally get a needle file through and really get to work.Ugh!
This signal will be on quite a short post as it is to go close to the footbridge that provides a photographic end to pics. of Leawarra yard.
I know possums run through here, and I'm not sure if they go over the bridge or under it. A pointy finial sticking up higher than the footbridge could be asking for trouble. It's also got to be in line with the gap under the bridge so that the interlocking (if we go there) can come through from the set of points further up the line.
Grant.
Then the horror job, Worrying (engineering term) a slot 1/16thx7/32" through a piece of 3/4" M.S. bar for the lever weight. My longest 1/16th end mill was about 1/4" long, so three 1/16th holes in a line, join them up with the end mill to 1/4" deep then the rest of the afternoon wearing away the bit in the middle till I could finally get a needle file through and really get to work.Ugh!
This signal will be on quite a short post as it is to go close to the footbridge that provides a photographic end to pics. of Leawarra yard.
I know possums run through here, and I'm not sure if they go over the bridge or under it. A pointy finial sticking up higher than the footbridge could be asking for trouble. It's also got to be in line with the gap under the bridge so that the interlocking (if we go there) can come through from the set of points further up the line.
Grant.
- Peter Butler
- Driver
- Posts: 5245
- Joined: Sun Sep 09, 2012 10:33 pm
- Location: West Wales
A classy piece of work there Grant... beyond my engineering capacity I think!
I love the idea of Possums using your railway footbridge, a tiny Vole joined me yesterday as I was working on my track, at least they are good company in the absence of real people.
I love the idea of Possums using your railway footbridge, a tiny Vole joined me yesterday as I was working on my track, at least they are good company in the absence of real people.
The best things in life are free.... so why am I doing this?
- Soar Valley Light
- Driver
- Posts: 1451
- Joined: Sun Dec 08, 2013 5:18 pm
- Location: North West Leicestershire
My 'Inspector of works' is a Robin! He's easily distracted from shoddy workmanship by brown envelopes (well, glass dishes actually!) filled with mealworms
Those signal fittings would be the envy of any S&T department in any scale Grant. I just know that you will have fitted the counterbalance weight with a working clamping screw! I look forward to seeing the finished signal in operation. I'd be simply delighted if I had manufacturing skills and facilities only a tenth as good as yours. :oops:
Andrew
Those signal fittings would be the envy of any S&T department in any scale Grant. I just know that you will have fitted the counterbalance weight with a working clamping screw! I look forward to seeing the finished signal in operation. I'd be simply delighted if I had manufacturing skills and facilities only a tenth as good as yours. :oops:
Andrew
"Smith! Why do you only come to work four days a week?
"'cause I can't manage on three gaffer!"
"'cause I can't manage on three gaffer!"
Grant doesn't.......Peter Butler:118295 wrote: I love the idea of Possums using your railway footbridge,
The possums in question are 'Brushies', the Common Brushtail Possum. Nocturnal, agile, about the size of a large house cat and devourers of fruits, vegies and garden plants.
They also bulldoze their way through any obstructions in their regular travel paths and are strong enough to lift roof tiles to take up residence in your roof space.
Just what every garden railway needs in residence.
Graeme
- Peter Butler
- Driver
- Posts: 5245
- Joined: Sun Sep 09, 2012 10:33 pm
- Location: West Wales
[Oops!!!!!! Dame Edna makes them sound so sweet!]
They might be, diced with some vegetables and a nice stock, simmered slowly for a couple of hours!!!!
Seriously, I respect all animals, though they frustrate me at times. The blackbirds though smaller create far greater damage, then repeat it next day after you've repaired it.
Grant.
They might be, diced with some vegetables and a nice stock, simmered slowly for a couple of hours!!!!
Seriously, I respect all animals, though they frustrate me at times. The blackbirds though smaller create far greater damage, then repeat it next day after you've repaired it.
Grant.
Who is online
Users browsing this forum: No registered users and 5 guests