5" gauge 0-6-0 Sweet Pea

Discussion of Live Steam locomotives should be located here
Post Reply
User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

5" gauge 0-6-0 Sweet Pea

Post by tom_tom_go » Sat Jul 13, 2019 5:40 pm

I snapped up this loco recently from SRS, it was posted on their site one morning and I had bought it before lunch time:

https://www.stationroadsteam.com/5-inch ... code-8639/

As it says in the description on the SRS site, a 'Metre Maid' is the 0-6-0 variant of 'Sweet Pea' which is probably the most popular model loco ever designed in 5" gauge.

Once the loco is delivered I will decide if I will keep her as a 'Metre Maid' (not sure about the tender yet) or scale her up to a larger narrow gauge looking loco (more like a Sweet Pea but an 0-6-0 variant like the below loco which was sold a while back from SRS):

https://www.stationroadsteam.com/5-inch ... code-6209/

Here is a short video I found on YouTube of a 'Metre Maid' to give you an idea of what a finished loco in steam looks and runs like although my one is built with Hackworth valve gear:



I plan to document here her time with me if it is of interest.

User avatar
Busted Bricks
Trainee Driver
Trainee Driver
Posts: 750
Joined: Sat Jan 22, 2011 9:16 pm
Location: Denmark
Contact:

Re: 5" gauge 'Metre Maid'

Post by Busted Bricks » Sat Jul 13, 2019 7:34 pm

Congratulations, that's a very nice loco. I'm sure you will get a lot of enjoyment out of that.

User avatar
idlemarvel
Trainee Fireman
Trainee Fireman
Posts: 136
Joined: Tue May 28, 2019 1:59 pm

Re: 5" gauge 'Metre Maid'

Post by idlemarvel » Sat Jul 13, 2019 7:37 pm

Wow that looks amazing. I'm sure you will have a great time with it. Please document what you do. I don't think I could get an 0-6-0 on my 9 ft radius curves :(
Dave Miller
currently building the 5" gauge Circle Line

User avatar
dewintondave
Trainee Driver
Trainee Driver
Posts: 697
Joined: Mon Mar 07, 2011 8:52 am
Location: New Zealand

Re: 5" gauge 'Metre Maid'

Post by dewintondave » Sat Jul 13, 2019 11:18 pm

Very nice Tom!
Best wishes,
Dave

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: 5" gauge 'Metre Maid'

Post by tom_tom_go » Sun Jul 14, 2019 11:50 am

Given the quality of workmanship and the price paid (cost less than most 16mm scale coal fired and even gas fired locos now) I am quite chuffed despite it not being quite what I wanted appearance wise (but it can be made to look narrow gauge like a Sweet Pea as the parts are interchangeable).

Blackgates Engineering do all the bits I need which has made me realise you don't have to be a skilled machinist with a fully kitted workshop to get along in the world of larger ride on railways:

http://www.blackgates.co.uk/

User avatar
idlemarvel
Trainee Fireman
Trainee Fireman
Posts: 136
Joined: Tue May 28, 2019 1:59 pm

Re: 5" gauge 'Metre Maid'

Post by idlemarvel » Sun Jul 14, 2019 9:32 pm

Hmmm. They do a 0-4-0 Sweet Pea as well, and there is one (I think) on ebay. Mustn't be tempted...
Dave Miller
currently building the 5" gauge Circle Line

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: 5" gauge 'Metre Maid'

Post by tom_tom_go » Mon Jul 15, 2019 5:49 pm

I would not want to take the risk in this scale buying a loco off eBay.

Most of the locos up for auction don't state they have a valid steam and hydraulic test or the locos steam test is about to expire (which means it will fail the steam test hence why they are selling it).

If you are serious about buying a loco then I would keep an eye on the SRS website as they don't sell crap, they offer a 14 day return policy and their prices are fair compared to other suppliers and even private sellers.

My loco should be arriving tomorrow!

User avatar
idlemarvel
Trainee Fireman
Trainee Fireman
Posts: 136
Joined: Tue May 28, 2019 1:59 pm

Re: 5" gauge 'Metre Maid'

Post by idlemarvel » Mon Jul 15, 2019 8:35 pm

Thanks for the advice. I wasn't serious about the eBay purchase. If I ever did get into live steam I probably wouldn't start at 5" gauge!
Dave Miller
currently building the 5" gauge Circle Line

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: 5" gauge 'Metre Maid'

Post by tom_tom_go » Tue Jul 16, 2019 3:19 pm

It's arrived!

IMG_20190716_151732-01.jpeg
IMG_20190716_151732-01.jpeg (392.36 KiB) Viewed 13117 times

User avatar
idlemarvel
Trainee Fireman
Trainee Fireman
Posts: 136
Joined: Tue May 28, 2019 1:59 pm

Re: 5" gauge 'Metre Maid'

Post by idlemarvel » Wed Jul 17, 2019 7:26 am

Well if nothing else it is well packed! :)
Dave Miller
currently building the 5" gauge Circle Line

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: 5" gauge 'Metre Maid'

Post by tom_tom_go » Sun Aug 04, 2019 5:14 pm

Before I started work on the loco I had to get my workshop sorted out which has taken time and I have had to push myself to get rid of wood, tools and items that maybe one day would be useful but have never been used. This has created a more open space and I feel better now working in there than I have done previously.

Roly supervising clean up work and then falling asleep as per cat protocol:

IMG_20190727_103001-01.jpeg
IMG_20190727_103001-01.jpeg (337.6 KiB) Viewed 12722 times
IMG_20190727_111109-01.jpeg
IMG_20190727_111109-01.jpeg (340.63 KiB) Viewed 12722 times

Due to the size and weight of the loco I was never going to be able to lift it and store it away on my own each time I wanted to tinker so I treated myself to a hydraulic lifting trolley (picture was taken during workshop reorganisation!):

IMG_20190722_211508-01.jpeg
IMG_20190722_211508-01.jpeg (370.45 KiB) Viewed 12722 times

It wasn't cheap, however, it's a well made sturdy piece of kit and as it is rated to lift up to 300kg I can use it with larger and heavier locos in the future ;)

The loco has been sitting for some time in the builder’s workshop (it's never been fired, however, it was sold with a new hydraulic test certificate so the boiler is sound) hence why the wheels on the driving axle were very difficult to rotate on first inspection. I removed the con rods from the pistons and found the chassis ran forwards and backwards freely so turned my attention to the cylinders.

The pistons were very hard to move backwards and forwards so with the cylinder covers removed I poured in generous amounts of light machine oil to help get things moving. After a good soak and repetitive movement they started to free up slightly but what is really required is hours of running on air as the cylinders and running gear have not had time yet to bed in.

I took the plunge and bought a new 2.5HP air compressor that can run at 9.5 CFM (Cubic feet per minute, I didn't know what it meant until I started researching compressors). It has a 25 litre tank so should be more than adequate for my needs plus it was supplied with a range of accessories for painting, air blasting, etc.

So, how to get her running on air? Each cylinder steam feed is silver soldered to the steam header so I couldn't connect the air line to the cylinders unless I invested in additional pipework to feed each cylinder individually.

I tried pumping air into the boiler via one of the clack valves, however, as you can see in the below video you cannot pump sufficient air into such small inlet to maintain pressure but at least she moved for the first time so it was quite exciting for me and I think the whistle sounds great!




I am fortunate to know a colleague who is always a WhatsApp message away with model engineering queries and after asking him what I should do he suggested that an adapter could be made to fit into one of the safety valve threads where a larger air line could be fitted. As he has one complete and a second in progress 'Sweet Pea' variant of this loco he already knew the size of the thread required for the adapter so he machined one up and it arrived in the post the next day:

IMG-20190802-WA0000-01.jpeg
IMG-20190802-WA0000-01.jpeg (150.38 KiB) Viewed 12722 times

I have a flexible 'whip hose' on order (again, didn't know what one of these were until I researched it!) so one end will connect to the adapter and the other to my airline as it is considered unsafe to have a fixed connection.

The cab on my loco is built to a high standard with neat soldering, however, it is far too squat for my liking and made removing one of the safety valves for the air line adapter impossible as you can see (you can't get a spanner in there!)

IMG_20190730_190221-01.jpeg
IMG_20190730_190221-01.jpeg (265.49 KiB) Viewed 12722 times

After much swearing and having to remove both the drain cock rod, reverser rod and blower pipe I managed to remove the cab (not like taking a Roundhouse cab off, a few bolts to remove and job done) and fit the air line adapter:

IMG_20190803_172304-01.jpeg
IMG_20190803_172304-01.jpeg (287.7 KiB) Viewed 12722 times

And so that takes us up to today where for the first time after nearing workshop reorganisation I had enough space to wheel the loco into the garden to take this photo with my Roundhouse Silver Lady so you get an idea of the size of her (I quite like the idea of having her without a cab at the moment, almost a 0-6-0 Quarry Hunslet Bagnall style monster creation!):

IMG_20190804_154355-01.jpeg
IMG_20190804_154355-01.jpeg (345.05 KiB) Viewed 12722 times

The chimney is too small so that will be replaced with a taller one (I received the workshop manual this weekend for the loco with all the drawings for parts that I want produced or replaced). I suspect I will fit a cab eventually.

If you have read this far you must of found it interesting!

IMG_20190804_171313-01.jpeg
IMG_20190804_171313-01.jpeg (325.41 KiB) Viewed 12722 times

User avatar
Busted Bricks
Trainee Driver
Trainee Driver
Posts: 750
Joined: Sat Jan 22, 2011 9:16 pm
Location: Denmark
Contact:

Re: 5" gauge 'Metre Maid'

Post by Busted Bricks » Sun Aug 04, 2019 5:30 pm

Very nice! A taller chimney and a Hunslet style open cab would look good on it.

User avatar
idlemarvel
Trainee Fireman
Trainee Fireman
Posts: 136
Joined: Tue May 28, 2019 1:59 pm

Re: 5" gauge 'Metre Maid'

Post by idlemarvel » Sun Aug 04, 2019 6:50 pm

Very interesting Tom. It sounds like you are learning a lot on the go. :)
Dave Miller
currently building the 5" gauge Circle Line

DonW
Fireman
Fireman
Posts: 261
Joined: Mon Jul 22, 2019 12:57 pm
Location: West Somerset

Re: 5" gauge 'Metre Maid'

Post by DonW » Sun Aug 04, 2019 11:46 pm

It looks very well made.

Don

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: 5" gauge 'Metre Maid'

Post by tom_tom_go » Mon Aug 12, 2019 9:50 pm

Second attempt on air was successful now that I have an adapter fitted in place of one of the safety valves allowing better flow rate into the boiler:



The new rolling road units from CMD Engineering are brilliant:

http://www.miniature-trains.co.uk/produ ... ling-road/

Nearly time to steam her up!

DonW
Fireman
Fireman
Posts: 261
Joined: Mon Jul 22, 2019 12:57 pm
Location: West Somerset

Re: 5" gauge 'Metre Maid'

Post by DonW » Tue Aug 13, 2019 8:01 am

Runs lovely on air. You are getting to the exciting bit next.

Don

User avatar
dewintondave
Trainee Driver
Trainee Driver
Posts: 697
Joined: Mon Mar 07, 2011 8:52 am
Location: New Zealand

Re: 5" gauge 'Metre Maid'

Post by dewintondave » Tue Aug 13, 2019 8:15 am

:thumbup:

It's nice to see a mechanical lubricator.

Snap! I'm making a rolling road set-up right now
Best wishes,
Dave

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: 5" gauge 'Metre Maid'

Post by tom_tom_go » Tue Aug 13, 2019 4:38 pm

dewintondave wrote: Tue Aug 13, 2019 8:15 am It's nice to see a mechanical lubricator.
Even better when it works unlike when I first filled it up (spot the problem):

Screenshot_20190813-163334-01.jpeg
Screenshot_20190813-163334-01.jpeg (267.31 KiB) Viewed 9650 times

It's fixed now as you can see in the video I posted yesterday!

User avatar
dewintondave
Trainee Driver
Trainee Driver
Posts: 697
Joined: Mon Mar 07, 2011 8:52 am
Location: New Zealand

Re: 5" gauge 'Metre Maid'

Post by dewintondave » Tue Aug 13, 2019 11:59 pm

tom_tom_go wrote: Tue Aug 13, 2019 4:38 pm
Even better when it works unlike when I first filled it up (spot the problem)
What is that liquid in the lubricator, not steam oil eh?
Best wishes,
Dave

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: 5" gauge 'Metre Maid'

Post by tom_tom_go » Thu Aug 15, 2019 9:43 am

As it's running on air I am using light machine oil.

Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests