Bolt together Mamod locomotive body.

A very popular starting point for Live Steam. With their low cost comes a number of problems which can be discussed here
Post Reply
User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Bolt together Mamod locomotive body.

Post by Tony Bird » Wed Dec 03, 2014 9:17 am

Hi,

Yesterday I had a bit of time and decided to finish the body on my BSA Mamod. As the Mamod locomotive as made has a lot of its body held together with 'Pop' rivets which make it a little difficult to work on. So if I am doing major work on a Mamod locomotive I usually drill out the 'Pop' rivets and replace them with 6BA/3mm nuts and bolts. First all the rivets are drilled out using the clearance size drill for the screws to be used 2.9/3.10mm. The smoke box rivets are usually replace by 5BA screws the smoke box being tapped for the screws and the hole in the boiler made larger to accommodate the screws, sometimes 6BA is used with a shouldered nut soldered inside the end of the boiler . As this boiler is a new hard soldered copper one the fixing points have been tapped 6BA. Regard the rest of the body just nuts and bolts are needed to attach the cab front to the foot plate. The four awkward ones are those that attach the cab front to the side tanks and the flame guard. For this bit it is helpful if you have access to a lathe to shoulder the nuts but I have used plain nuts soldered or glued in place. If shouldered nuts are being used the holes where they will fit are made larger I used a 4mm drill. The shouldered nuts are soft soldered in place if the model is to be repainted or glued (Standard Araldite) in place. I think I would always solder the nuts in the flame guard I used ordinary B&Q's plumbers solder and flux.

I hope the photographs show the process of fitting the nuts.


Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image

Regards Tony.

User avatar
MDLR
Driver
Driver
Posts: 4027
Joined: Thu Jan 15, 2009 10:38 pm
Location: Near Ripley, Derbyshire, UK
Contact:

Post by MDLR » Wed Dec 03, 2014 9:50 am

That looks rather stylish - it smacks of the "Gentleman's Sporting Loco" which Brian Clarke used to make (but his was battery electric).
Brian L Dominic
Managing Director
Flagg Fluorspar Co
www.mdlr.co.uk/ff.html

Big Jim
Moderator
Moderator
Posts: 2694
Joined: Sat Jul 06, 2013 5:28 pm
Location: Near Llanelli

Post by Big Jim » Wed Dec 03, 2014 10:24 am

Very good.

User avatar
IrishPeter
Driver
Driver
Posts: 1400
Joined: Wed Feb 23, 2011 3:24 am
Location: 'Boro, VA

Post by IrishPeter » Wed Dec 03, 2014 3:21 pm

Well done! Finally, a Mamod that I do not hate the look of on sight.

Cheers,
Peter in AZ
Traffic Pattern? What pattern? Spuds out; grain in, but cattle, sheep and passengers are a lot less predictable.

User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Post by Tony Bird » Wed Dec 03, 2014 3:49 pm

Hi Brian,

That looks rather stylish - it smacks of the "Gentleman's Sporting Loco" which Brian Clarke used to make (but his was battery electric).

I was thinking more of a 7/8" scale Gas Works locomotive?

Regards Tony.

big-ted
Trainee Fireman
Trainee Fireman
Posts: 235
Joined: Fri Nov 25, 2011 4:13 pm
Location: Vancouver, BC, Canada.

Post by big-ted » Wed Dec 03, 2014 7:33 pm

Looks great, I'm curious though. If you're going through all this trouble, why not use (presumably far more common and easily attainable) M3 hardware rather than 6BA?

User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Post by Tony Bird » Thu Dec 04, 2014 9:29 am

Hi Ted,

I'm curious though. If you're going through all this trouble, why not use (presumably far more common and easily attainable) M3 hardware rather than 6BA?

The reason for using 6 BA rather than M3 is that certainly the older Mamod locomotives and maybe the later ones use 6 BA. In this case as the model is being made from bits and pieces that I have has no existing screws. I could have used M3 but the buffer beams would have had to be tapped M3 or accept the use of different threads for the same size on the model.

Regards Tony.

User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Post by Tony Bird » Tue Dec 16, 2014 10:51 am

Hi,

A bit more progress. The frames have been painted, the reversing block sealed in place and insulated buffer beams fitted.


Image
Image
Image

Trunnions for the cylinders have to be made so the chassis can be tested on air.

Regards Tony.

User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Post by Tony Bird » Wed Dec 17, 2014 9:03 am

Hi,

The cylinders have been fitted to the chassis so it might get a run on air today.

Image

Image

Image

Regards Tony.

User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Post by Tony Bird » Wed Dec 17, 2014 5:24 pm

Hi,

Ran the chassis on air today.

Image

Video.

Image

Regards Tony.

User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Post by Tony Bird » Mon Feb 16, 2015 4:39 pm

Hi,

I haven't done any work on this Mamod locomotive since the middle of December! When the chassis was run on air.

I started back on it yesterday When it looked like this.

Image

The cab bits have been painted, a regulator has been part made, the steam and exhaust pipes have been fitted, a driver has been found and all the screws needed were cut to size and finished. So at end of play today the model looked like this.

Image
Image
Image
Image

To complete the model the regulator has to be finished, a lubricator made and fitted and a burner made.

Regards Tony.

User avatar
MDLR
Driver
Driver
Posts: 4027
Joined: Thu Jan 15, 2009 10:38 pm
Location: Near Ripley, Derbyshire, UK
Contact:

Post by MDLR » Mon Feb 16, 2015 5:54 pm

That's looking very nice! Incidentally, when you were testing the chassis, where was the orchestra?
Brian L Dominic
Managing Director
Flagg Fluorspar Co
www.mdlr.co.uk/ff.html

User avatar
Dannypenguin
Trainee Driver
Trainee Driver
Posts: 632
Joined: Tue Feb 26, 2013 9:57 am
Location: Forest of Dean, UK
Contact:

Post by Dannypenguin » Mon Feb 16, 2015 6:01 pm

Like! :D
Dan

Visit the PFLR website - http://poultonfarmlightrailway.webs.com/
Dean Forest Railway Society website - http://dfrsociety.org/

User avatar
Dr. Bond of the DVLR
Retired Director
Retired Director
Posts: 4481
Joined: Tue Jun 09, 2009 9:43 pm
Location: Suffolk
Contact:

Post by Dr. Bond of the DVLR » Mon Feb 16, 2015 6:24 pm

Lovely and neat - the cut off chimbley really makes the lines of this loco.
Image
The railway which people forgot
(to build)

User avatar
Tony Bird
Trainee Driver
Trainee Driver
Posts: 568
Joined: Thu Jul 29, 2010 8:25 am
Location: Cardiff, South Wales, UK.

Post by Tony Bird » Tue Feb 17, 2015 8:24 am

Hi Brian,

Incidentally, when you were testing the chassis, where was the orchestra?

As I was holding the camera I had only one hand to conduct and it was a little tight for the rest of the musicians in my shed! See you at the AGM.

Regards Tony.

Big Jim
Moderator
Moderator
Posts: 2694
Joined: Sat Jul 06, 2013 5:28 pm
Location: Near Llanelli

Post by Big Jim » Tue Feb 17, 2015 8:35 am

That looks rather good Tony.

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests