Etch primer and painting advice

Do you have a problem? Here is the place to appeal for help
Post Reply
User avatar
steamgeorge
Trainee Fireman
Trainee Fireman
Posts: 139
Joined: Mon Sep 18, 2017 9:31 am
Location: Oxforshire, UK
Contact:

Etch primer and painting advice

Post by steamgeorge » Mon Jun 01, 2020 2:09 pm

Hi

Just stripping the paint off a 1984 Roundhouse Lady Anne. I say stripping - it doesn't require any chemical stripping as it is just all flaking off leaving a lovely brass finish! Just a couple of questions if I may please...

What brass etch primer are people using at the moment? Upol acid 8 ?
Recommendations for paint to spray the smokebox (I'd like matt black) and body (I'd like satin black)? All will need to be rattle cans please.

Any recommendations would be much appreciated.

Best wishes
George

User avatar
tom_tom_go
Driver
Driver
Posts: 4824
Joined: Wed Feb 23, 2011 3:08 am
Location: Kent, UK
Contact:

Re: Etch primer and painting advice

Post by tom_tom_go » Mon Jun 01, 2020 5:53 pm

Chris Bird does a good paint guide using rattle cans:

https://sites.google.com/a/gardenrailwa ... e-easy-way

cncmodeller
Trainee Fireman
Trainee Fireman
Posts: 233
Joined: Sat May 11, 2013 4:15 pm
Location: lincolnshire

Re: Etch primer and painting advice

Post by cncmodeller » Mon Jun 01, 2020 11:03 pm

There is only one and believe me I've tried them all, It's called Hammerite special metal primer it's water based [ although you'd never guess ] and I actually sprayed it but thinned it only very slightly, it dries very quickly and is very good. When I sprayed the boiler of my Archangel Princess I went back to scratch the paint off below where the wicks are and is was quite a job, normally it just falls off with other 'Etch' primers.
Those rattle cans of etch primers you see are great for steel but Brass is a difficult one.
If you're into painting with a brush you would have to work quite quickly and neatly, but take it from me get yourself a spray gun and do a proper job.

John

User avatar
Andrew
Moderator
Moderator
Posts: 3247
Joined: Tue Jul 03, 2012 1:33 pm
Location: Bristol, UK
Contact:

Re: Etch primer and painting advice

Post by Andrew » Tue Jun 02, 2020 8:15 am

Hi George,

I used barbecue paint on the smokebox of my Bertie and was pleased with how that turned out - think I used it on the cab roof and running plate too, with the rest of the body remaining in RH gloss black. That came in a spray can, probably from B&Q.

Actually, that may have been a tip from Chris Bird's article that Tom sent a link to...

Good luck with the project,

Andrew.

User avatar
Andrew
Moderator
Moderator
Posts: 3247
Joined: Tue Jul 03, 2012 1:33 pm
Location: Bristol, UK
Contact:

Re: Etch primer and painting advice

Post by Andrew » Tue Jun 02, 2020 8:16 am

PS, yes, used UPol last time I etch-primed something. Halfords supply that... Cheers!

User avatar
steamgeorge
Trainee Fireman
Trainee Fireman
Posts: 139
Joined: Mon Sep 18, 2017 9:31 am
Location: Oxforshire, UK
Contact:

Re: Etch primer and painting advice

Post by steamgeorge » Tue Jun 02, 2020 12:46 pm

Thank you - I'll let you know how I get on

Garethh
Trainee Fireman
Trainee Fireman
Posts: 219
Joined: Wed Apr 22, 2020 8:39 am
Location: Surrey

Re: Etch primer and painting advice

Post by Garethh » Wed Jun 03, 2020 6:14 am

Whatever you do don’t use halfords own brand etch primer, I bought some when they’d run out of upol and wasn’t happy with the results!

User avatar
MRail
Trainee Fireman
Trainee Fireman
Posts: 116
Joined: Mon Oct 26, 2009 4:16 pm
Location: Merseyside, UK
Contact:

Re: Etch primer and painting advice

Post by MRail » Wed Jun 03, 2020 9:05 am

I second that.
The data says for zinc & galvanised metals, such as steel. ie car body repairs.
Somewhere, I can no longer find, I once saw "will not adhere to brass".
I don't understand it's popularity.
Rob G
Madog & Mersey Railway (SM32)
In my Father's roundhouse are many loco sheds.

cncmodeller
Trainee Fireman
Trainee Fireman
Posts: 233
Joined: Sat May 11, 2013 4:15 pm
Location: lincolnshire

Re: Etch primer and painting advice

Post by cncmodeller » Wed Jun 03, 2020 9:13 am

I don't think a lot of modellers understand the difference between paint just 'sitting' on brass and paint actually adhering to it and not knocking off on edges and corners with minimal use.
John

User avatar
Jimmyb
Fireman
Fireman
Posts: 492
Joined: Sat Nov 23, 2019 10:43 pm
Location: Weston-super-Mare

Re: Etch primer and painting advice

Post by Jimmyb » Wed Jun 03, 2020 12:08 pm

cncmodeller wrote: Mon Jun 01, 2020 11:03 pm There is only one and believe me I've tried them all, It's called Hammerite special metal primer it's water based [ although you'd never guess ] and I actually sprayed it but thinned it only very slightly, it dries very quickly and is very good.

John
Not that I didn't believe you, just done a search, but it seems it is only in red!

cncmodeller
Trainee Fireman
Trainee Fireman
Posts: 233
Joined: Sat May 11, 2013 4:15 pm
Location: lincolnshire

Re: Etch primer and painting advice

Post by cncmodeller » Wed Jun 03, 2020 1:15 pm

Spot on! it's an etch primer that actually works on brass.
John

User avatar
Andrew
Moderator
Moderator
Posts: 3247
Joined: Tue Jul 03, 2012 1:33 pm
Location: Bristol, UK
Contact:

Re: Etch primer and painting advice

Post by Andrew » Wed Jun 03, 2020 4:44 pm

Jimmyb wrote: Wed Jun 03, 2020 12:08 pm
cncmodeller wrote: Mon Jun 01, 2020 11:03 pm There is only one and believe me I've tried them all, It's called Hammerite special metal primer it's water based [ although you'd never guess ] and I actually sprayed it but thinned it only very slightly, it dries very quickly and is very good.

John
Not that I didn't believe you, just done a search, but it seems it is only in red!
I missed that initially - sounds very promising, thanks for the tip...

Andrew

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests