Bogies

Do you have a problem? Here is the place to appeal for help
User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Bogies

Post by FWLR » Sat Jul 06, 2019 10:28 am

I need some advice please on some bogies. I have a railbus that will not run at all on my newly laid extension track, it wouldn't run on the old track either.... :lol: The trouble is I think, the bogies are too far forward and the whole body rolls all the time. I am thinking that the bogie needs to be moved back a fair bit, but the trouble is there is a battery box fixed under the body so I can only move it back to a certain point.
What I am really asking is, are there any bogies that have single axles or will I need to make my own. If I need to make my own what is the easiest why of doing it please.


Couple of photos of the wheels.
DSCN4057.JPG
DSCN4057.JPG (448.35 KiB) Viewed 6661 times
DSCN4058.JPG
DSCN4058.JPG (463.66 KiB) Viewed 6661 times
DSCN4059.JPG
DSCN4059.JPG (415.42 KiB) Viewed 6661 times

This is a little video of the extension. The tram is a little bit noisy, but hopefully she will get quieter with some dry grease on the drive.... :roll: She is also pulling the coach that wouldn't run on the old track..


User avatar
GTB
Driver
Driver
Posts: 1550
Joined: Sat Mar 05, 2011 2:46 pm
Location: Australia

Re: Bogies

Post by GTB » Sat Jul 06, 2019 12:23 pm

FWLR wrote: ↑Sat Jul 06, 2019 10:28 am I need some advice please on some bogies.
Loosen the bogie mounting screw so the bogie can tilt fore and aft and rock side to side, as well as rotate freely.

Since the rear driving axle is presumably fixed in position, that will give you 3 point suspension and make the model less sensitive to the track. You may have to experiment a bit to work out how much freedom the bogie needs on this track.

Same with bogie coaches (and bogie wagons), one bogie needs side bearers to stop it rocking, but still be free to tilt back and forward. The other one needs to be free to both rock and tilt, again to give a 3 point suspension.

The bogie wheelbase looks short, so unless your tracklaying is really bad, you shouldn't need to fit a bogie with compensated sideframes.

Have fun..... ;)

Regards,
Graeme

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Sat Jul 06, 2019 4:08 pm

Thanks Graeme. Did you look at the tram video, it shows it running with a coach that would not run at all on the old track. It does now, so I think the track is fairly well laid if I say so myself.... :lol: :lol:

User avatar
GTB
Driver
Driver
Posts: 1550
Joined: Sat Mar 05, 2011 2:46 pm
Location: Australia

Re: Bogies

Post by GTB » Mon Jul 08, 2019 1:46 pm

FWLR wrote: ↑Sat Jul 06, 2019 4:08 pm so I think the track is fairly well laid if I say so myself....
I don't doubt that, but we live in a universe where entropy increases.... The odds are the track will move over time.

Mine is partly built on fill and I'm already seeing slight gradients that weren't there when I built it...... :roll:

Which is why the supports are designed to be easily adjustable.

The coach may be OK now on good track, but it would still be worth sorting it out, so you can run it on other tracks that aren't as well laid as yours.

Regards,
Graeme

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Mon Jul 08, 2019 4:42 pm

I do see what you are saying Graeme and your are correct in that track will over time move, I am hoping that mine will not, he says with some anticipation...... :lol: :lol: :lol:

User avatar
MRail
Trainee Fireman
Trainee Fireman
Posts: 116
Joined: Mon Oct 26, 2009 4:16 pm
Location: Merseyside, UK
Contact:

Re: Bogies

Post by MRail » Tue Jul 09, 2019 7:32 am

Rod,
This looks like a Brandbright railcar?
If so, I had one for a while, and it displayed all the troubles you mention.
The problem is, it's simply too long for our typically sharp curves.

I moved the battery box further back, and then refitted the bogie pivot under the front bulkhead.
[attachment=0]MR070707-14.jpg[/attachment]

It still wasn't enough, so it was sold on.
Attachments
MR070707-14.jpg
MR070707-14.jpg (47.77 KiB) Viewed 6552 times
Rob G
Madog & Mersey Railway (SM32)
In my Father's roundhouse are many loco sheds.

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Wed Jul 10, 2019 9:02 am

MRail wrote: ↑Tue Jul 09, 2019 7:32 am Rod,
This looks like a Brandbright railcar?
If so, I had one for a while, and it displayed all the troubles you mention.
The problem is, it's simply too long for our typically sharp curves.

I moved the battery box further back, and then refitted the bogie pivot under the front bulkhead.
MR070707-14.jpg

It still wasn't enough, so it was sold on.
Mmmmm you are spot on Rob, it is the very same Railcar....The quandary is, do I attempt to try and do the same, with perhaps moving the bogies even further back, or do I sale it on like you did, and how much should I sale it for....decisions, decisions.....Is it worth the aggro.....

PS Rob, did yours have larger wheels on the drive like mine and would that make it do what it does ?

User avatar
MRail
Trainee Fireman
Trainee Fireman
Posts: 116
Joined: Mon Oct 26, 2009 4:16 pm
Location: Merseyside, UK
Contact:

Re: Bogies

Post by MRail » Wed Jul 10, 2019 4:29 pm

Yes, Rod,
Pretty much the same. Of course, it was some years back.
Bought it in 2003 & finally sold it about 2010.
I seem to remember it was reasonably stable, just ground to a halt on my curves.

I felt it would benefit from a 4w power bogie at the rear, but couldn't locate anything suitable.
Just wondering perhaps a Lima 0 gauge bogie, with false side frames might do the trick.
They occasionally come up on that well known auction site.
Rob G
Madog & Mersey Railway (SM32)
In my Father's roundhouse are many loco sheds.

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Thu Jul 11, 2019 6:33 am

Thanks Rob... :thumbright:

I will stick with it then and see how it goes, I am one for not giving up on something and if I can get it to work well all well and good, but if not..... :roll: :roll:

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Thu Jul 11, 2019 7:06 am


User avatar
Peter Butler
Driver
Driver
Posts: 5219
Joined: Sun Sep 09, 2012 10:33 pm
Location: West Wales

Re: Bogies

Post by Peter Butler » Thu Jul 11, 2019 3:46 pm

Hi Rod, I have just checked out that link to bogies and those are not the ones you need. What is suggested by Rob is an '0' gauge power bogie (4 wheel drive with motor unit attached) made by LIMA. These are now no longer made and highly sought after, so can be expensive. You might be lucky enough to find a complete diesel loco for sale which uses these but you will have to be prepared to spend some serious cash.
If you can find one which doesn't work electrically but the gears are still good, you can get replacement motors which are easy to fit, and alter to battery power instead of track power.
The best things in life are free.... so why am I doing this?

User avatar
MRail
Trainee Fireman
Trainee Fireman
Posts: 116
Joined: Mon Oct 26, 2009 4:16 pm
Location: Merseyside, UK
Contact:

Re: Bogies

Post by MRail » Fri Jul 12, 2019 9:02 am

Sorry, a bit slow chipping in, been busy in the works.
Yes, Peter, that's correct.
I'm wondering now if something from IP Eng. may be adaptable.
Rob G
Madog & Mersey Railway (SM32)
In my Father's roundhouse are many loco sheds.

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Sat Jul 13, 2019 8:56 am

What about these ?

https://www.ipenginnering.com/product-p ... nce-bogies.

Or something similar...

User avatar
MRail
Trainee Fireman
Trainee Fireman
Posts: 116
Joined: Mon Oct 26, 2009 4:16 pm
Location: Merseyside, UK
Contact:

Re: Bogies

Post by MRail » Sat Jul 13, 2019 9:20 am

Sorry Rod, No, it needs a motorised bogie.

This sort of thing MAY be adaptable:-

[attachment=0]IP Bogie.jpg[/attachment]
Attachments
IP Bogie.jpg
IP Bogie.jpg (34.84 KiB) Viewed 6363 times
Rob G
Madog & Mersey Railway (SM32)
In my Father's roundhouse are many loco sheds.

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Sat Jul 13, 2019 9:56 am

Can you please explain to this uneducated mind..... :scratch: :lol: :lol:

I don't understand why it's needs to be a motorised bogie. Have I to replace the drive at the rear, or is it to put on the front bogies with it driven by the same batteries that are powering the rear wheels.....It's stupid I know..... :roll: :roll:

User avatar
MRail
Trainee Fireman
Trainee Fireman
Posts: 116
Joined: Mon Oct 26, 2009 4:16 pm
Location: Merseyside, UK
Contact:

Re: Bogies

Post by MRail » Sat Jul 13, 2019 12:24 pm

Sorry Rod,

My theory is to leave the front bogie as is.
Replace the rear, fixed, single axle drive with a swivelling 4w motor bogie.

This ought to make it comfortable on curves, like a bogie coach, (or Fairlie loco).
It is a bit radical, but I can't see a better way to do it.
Rob G
Madog & Mersey Railway (SM32)
In my Father's roundhouse are many loco sheds.

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Sat Jul 13, 2019 12:58 pm

I see now Rob. Thanks. :thumbright: :thumbright:

I will have a look at doing something with the back fixed drive.

User avatar
Peter Butler
Driver
Driver
Posts: 5219
Joined: Sun Sep 09, 2012 10:33 pm
Location: West Wales

Re: Bogies

Post by Peter Butler » Sat Jul 20, 2019 2:32 pm

I have been searching for a Lima motor bogie myself and found nothing available, so I thought laterally (as I usually do) and came up with an alternative. I must admit this is experimental and not the easiest of conversions to make, but it looks OK and should be up to the job...... what is it.....
IMG_6526.JPG
IMG_6526.JPG (131.31 KiB) Viewed 7270 times
A LEGO power bogie.... 9v and built to be child-resistant.... if that is possible?

After some surgery I have managed to reduce the width, replace the wheels and re-build the casing.....
IMG_6527.JPG
IMG_6527.JPG (121.14 KiB) Viewed 7270 times
IMG_6528.JPG
IMG_6528.JPG (130.03 KiB) Viewed 7270 times
These do come up for sale and are considerably cheaper than the Lima ones.

Not to every-ones liking, but I'm sure I can make use of it.
The best things in life are free.... so why am I doing this?

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Sat Jul 20, 2019 2:40 pm

Wow Peter, that's fantastic...... :thumbright: :thumbright:

It also looks like a Lego bogie with those dimples on it. Looks like I will need to be looking for one just like yours then.... :thumbright:.

Opppps, my flipping eyesight is going to..... :lol: :lol: :lol:

Thats what you get for not fully reading posts..... :lol: :lol: :lol:

User avatar
FWLR
Driver
Driver
Posts: 4262
Joined: Sat Aug 05, 2017 9:45 am
Location: Preston, Lancashire, UK

Re: Bogies

Post by FWLR » Sat Jul 20, 2019 2:54 pm

Just had look on Ebay Peter, would this be similar to the one you bought and could it be used on the railcar....

https://www.ebay.co.uk/itm/Lego-Power-F ... SwONlc~Blp

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests