Garden Railway Forum

They must have existed but not yet tracked one down.

Of course, the Peckforton Light Railway is a three-foot line with two two-foot feeders (copper mine and sand quarry) ....

Welcome to the forum BTW

Rik

Almost forgot. Some skip wagons have inside frames. You'd need to shorten the wheelbase, though.
Rik

The only inside framed wagons I can think of were early chaldron wagons. No doubt there were other styles.
Rik

Paint job looks fine to me, Steve. I'm never sure about having a high gloss finish on ng locos. I tend to dull mine down with a coat of satin lacquer anyway.

Rik

Rik, Even though the temp outside hasn't been that hot inside a shed the temp could be up to or greater than twice the outside temp. I had a opaque polycarbonate patio roof at a previous house and the temp under was far hotter than the air temp and it was open on 3 sides. Cars internal temp here ca...

I'm in favour of stakes to mark out the track-bed. I drove them into the ground, so their tops showed the intended track level around the garden (except where there was a below ground level cutting.... )

Rik

PS. It's probably advisable to protect the link from P3 to the soundcard with a 1k resistor, or maybe even a 4.7k resistor if you're powering the soundcard with 7.4v Rik PS - Now corrected the label for the switch and added the 1k resistor to the wiring diagram (see above) I am no electrician nor t...

PS. It's probably advisable to protect the link from P3 to the soundcard with a 1k resistor, or maybe even a 4.7k resistor if you're powering the soundcard with 7.4v

Rik
PS - Now corrected the label for the switch and added the 1k resistor to the wiring diagram (see above)

BTW, 2 questions... what's a DPDT Socket ?? :lol: :lol: ( Sorry, couldn't resist it! :oops: ) More seriously, what do you use to produce the lovely schematic diagrams like this one. It obviously doesn't take all that long to do, given the response time from my post to your reply. Ooops! I copied an...

-steves- wrote: ↑Sun Mar 31, 2024 9:49 am That's pretty much the wiring I used for mine, but without the buck convertor, the sound card I bought can handle 2 x li-ion batteries (8.4v) with no issue so just run them direct from the power input of the RX.

That's useful to know. I just assumed it would require 5v

Rik

I've powered my soundcard through an adjustable step-down buck converter set to 5v

Rik

EDIT2: Now corrected label for switch and added a 47R resistor between P1 and the LED

I was asked on Youtube about the hauling capabilities of the loco. At the time, I had no idea. But I added couplings yesterday and so today did a highly sophisticated load test - basically adding wagons until the wheels just started slipping. It took 13 LGB skips plus a brake van. Far more than I wi...

Thanks chaps. Yes, I've decided to replace all the roofs with plasticard. I can see the other roofs ending up like this eventually.

Rik

I have now made three models of an early version of the Southwold Railway Cleminson coaches. The first one is now a couple of years old. Its roof was made from five 3D printed sections glued together. After fixing the passengers inside, I decided to glue down the roof using prototypical arched batte...

dudeface wrote: ↑Sat Mar 30, 2024 1:19 am Wrench? They don't even know what they're selling...

-steves- wrote: ↑Tue Mar 19, 2024 2:44 pm I do hope you always disconnect the power before making your rapaies!

It's spelled "repaies" dontcha know.

At least they didn't put "wench" ....

Rik

Yup, a standard 603c will work straight out the box using pin 1 onto the white signal wire of the soundcard. Obviously with all negatives and positives attached :thumbup: If for some bizarre reason it doesn't then you can reprogramme using 2,1,1,1,1 I thought P1 on a standard MR603 gave forward lig...

Looks like this, maybe? I've not found the significance of the oak leaf wreath

Rik

Wow. That is a sorry spectacle. You did amazingly well on those dimensions, Philip. My model is more of a compromise as I had to make it fit the HGLW chassis and cab.

Rik

Not sure if it's their reason, but when I was running RC Trains, I stopped selling to distant non EU countries basically because Sod's Law applied in a couple of cases and their kit developed faults. Annoying as I had very few returns overall. I had to cover their return postage costs and also the c...

Can you borrow a prog 4 to programme it with, or borrow a different TX, like a TX20? I have a Prog4 but it no longer works with the serial cables/Coolterm.. it's all obsolete. Nobody I know within half a days journey to borrow from ( I think you are about the nearest! :roll: ) unfortunately and it'...