Hi,
Using a viper loco 10 ESC.
Kind regards
Neil
Search found 13 matches
- Sat Jun 08, 2019 9:37 pm
- Forum: Garden Railway Technical Help & Advice
- Topic: Micron radio control
- Replies: 10
- Views: 6320
- Sat Jun 08, 2019 8:51 pm
- Forum: Garden Railway Technical Help & Advice
- Topic: Micron radio control
- Replies: 10
- Views: 6320
Re: Micron radio control
Hi all,
Sorry for the delayed reply-just got back in the country. I have a TX22 transmitter and a n RX102 receiver. I have tried the suggested but it does nothing. Any suggestions?
Kind regards
Neil
Sorry for the delayed reply-just got back in the country. I have a TX22 transmitter and a n RX102 receiver. I have tried the suggested but it does nothing. Any suggestions?
Kind regards
Neil
- Mon Jun 03, 2019 8:26 pm
- Forum: Garden Railway Technical Help & Advice
- Topic: Micron radio control
- Replies: 10
- Views: 6320
Micron radio control
Hi all, I recently purchased a Micron transmitter and receiver from eBay. I have successfully installed in my Mamod Boulton. While it works it doesn't correspond with the controls on the transmitter. I have the rotary speed, inertia and direction switch. The direction switch doesn't work but the rot...
- Mon May 20, 2019 8:28 pm
- Forum: Mamods & MSS
- Topic: Mamod Stirling
- Replies: 29
- Views: 30486
Re: Mamod Stirling
Why is everyone so quick to shout this loco down? We aren't going to encourage anyone to build better locos if we slate it before it's been properly reviewed. From my perspective it is a nice looking loco with decent proportions and decent sized cylinders etc. Yes the roundhouse basic series are abo...
- Sun Jan 28, 2018 1:44 pm
- Forum: Mamods & MSS
- Topic: Mamod Stirling
- Replies: 29
- Views: 30486
Mamod Stirling
Hi All,
according to Mamod, the Stirling loco is on hold. That's what they told me when I asked them through facebook the other day. I was looking forward to some reviews on the Stirling as I really like the look of it.
kind regards
Neil
according to Mamod, the Stirling loco is on hold. That's what they told me when I asked them through facebook the other day. I was looking forward to some reviews on the Stirling as I really like the look of it.
kind regards
Neil
- Tue Jan 02, 2018 10:35 pm
- Forum: Mamods & MSS
- Topic: Mamod Brunel canopy
- Replies: 1
- Views: 3209
Mamod Brunel canopy
Hi,
Just seen the newly released canopy for the Mamod Brunel loco. Has anyone ordered one?
Neil
Just seen the newly released canopy for the Mamod Brunel loco. Has anyone ordered one?
Neil
- Sun Dec 17, 2017 2:31 pm
- Forum: Mamods & MSS
- Topic: Mamod Brunel
- Replies: 13
- Views: 12257
Re: Mamod Brunel
Does anyone know what thread type the water fill valve is on top of the boiler on the Brunel? \I sam thinking about fitting a whistle.
- Fri Dec 01, 2017 6:59 am
- Forum: Mamods & MSS
- Topic: Mamod Brunel
- Replies: 13
- Views: 12257
Re: Mamod Brunel
Yes, the photos are out of order. But, hopefully you can see the piping arrangement-that was the point. The tank is held in place with a spring clip similar to the gas tank. The brass bit lying on the floor is a wind down handbrake which has yet to be fitted.
- Tue Nov 28, 2017 9:29 pm
- Forum: Mamods & MSS
- Topic: Mamod Brunel
- Replies: 13
- Views: 12257
Re: Mamod Brunel
Hi all, a few more photos to show the condensate tank.
- Sun Nov 26, 2017 9:14 pm
- Forum: Mamods & MSS
- Topic: Mamod Brunel
- Replies: 13
- Views: 12257
Re: Mamod Brunel
Hi, yes the exit pipe that dissapears over the side of the loco has a blanking rivet in place. To emory the tank you need to removed the silicon pipe with blank. Remove the 'chimney' from the top and fit the short silicon pipe with blanking rivet. The steam from the cylinder will pish out the oil an...
- Sun Nov 26, 2017 8:26 am
- Forum: Mamods & MSS
- Topic: Mamod Brunel
- Replies: 13
- Views: 12257
Re: Mamod Brunel
Sorry, yes one photo doesn't have the copper pipe as it was during fitting/laying out
- Sun Nov 26, 2017 8:24 am
- Forum: Mamods & MSS
- Topic: Mamod Brunel
- Replies: 13
- Views: 12257
Re: Mamod Brunel
Hi, the condenser tank is from Clevedon steam, it has three connections. The top one is the exhaust, one side is the steam in and the other is the drain. To drain the tank you need to block off the exhaust and use the steam pressure to blow out the water. The reason for not putting the exhaust next ...
- Tue Nov 21, 2017 7:58 pm
- Forum: Mamods & MSS
- Topic: Mamod Brunel
- Replies: 13
- Views: 12257
Mamod Brunel
WP_20171102_20_47_15_Pro.jpg Hi all, I am new to this forum and 16mm steam. I also model g scale trams. I have recently bought a Mamod Brunel, and ran it for the first time on tracks the other week. I have fitted a Clevedon Steam condensate tank and fashioned a chimney out of a coffee machine part!...